What Thickness of Corten Steel Do You Actually Need?

Rusted letter R for Agnes Water Active Riders

What thickness of corten steel you need depends on the product. 3mm suits 3D letters and numbers and many gates, and 3 to 10mm suits sculpture. Those numbers answer most projects, and this guide explains why each one is what it is.

We are COR10 Steel, a custom corten fabricator in Byron Bay, NSW. We build 3D letters, sculptures, gates, fencing, parcel boxes, and signage from weathering steel. Most buyers ask this question backwards. They ask how thick the steel must be to stop it rusting through. Rusting through rarely decides the thickness for most garden pieces. Stiffness, heat, and impact decide it instead. Near the sea or in wet soil, corrosion earns its vote back.

The 30 Second Answer

Match the thickness to the job, not the fear. The table below gives the working range for our main products.

ProductThickness that worksThe reason in brief
3D letters and numbers3mmOur workshop spec, rigid enough for wall mounting
Sculpture3 to 10mm and upStructural needs grow with size
Gates3mm steel, hot-dip galvanisedOur Arcadia reference, four gates at 250kg each

3mm is our own confirmed spec for 3D letters and numbers. The Arcadia gates are our own built work. Other products are quoted per project, because the right thickness depends on size, site, and use. Read on for the reasoning behind every number.

Why Thickness Is Rarely About Rusting Through

0.01mm per year is the measured corrosion rate once corten’s patina stabilises. That figure comes from peer reviewed testing of 14 patina samples using X-ray diffraction. At that rate, garden steel has decades of atmospheric life.

The patina needs 3 to 7 years of wet and dry cycling to build. SSAB’s 32 year Finland field test showed corrosion dropping drastically after the first 5 years. Their stated range for the final appearance is 2 to 6 years.

Buried steel, ponded water, and permanently damp soil defeat the mechanism. The steel never gets its dry cycle, so the protective layer never stabilises. Detail every piece to drain and dry.

Context matters for the engineering numbers. 1.5mm per exposed face is the corrosion allowance for C4 environments in steelconstruction.info guidance, but that guidance comes from UK bridge design with a 120 year design life. Two faces at 1.5mm is 3mm of allowance, which equals our 3mm letters. The honest reading is that garden pieces in mild inland air live comfortably within these numbers, while coastal sites like Byron Bay deserve thicker steel or sealing. That is why our seaside sculptures get sealed. See our guide to how weathering steel works for the full patina story.

Sculpture, 3 to 10mm and Up

Size decides the thickness for corten sculpture, and the working range is 3 to 10mm and up. Small garden pieces work at 3mm. Large structural pieces need plate.

Memorial scale work shows the upper end. The Battle of Bannockburn signage used 5mm laser cut corten over 10mm backing plate, documented by AZoM. That is what public scale demands.

Coastal air is the honest limit. The FHWA’s Technical Advisory 5140.22 lists coastal environments among those where uncoated weathering steel should be used with caution, because airborne chlorides stop the protective patina forming.

Sealing is our professional position for seaside work. Our view is that sculptures near the sea should weather 12 months, then be sealed with Penetrol. It stops further weathering and runoff. Reapply it when it fades. See our custom sculpture cost guide and our sculpture range.

Gates, Our Arcadia Reference

3mm steel at around 250kg per gate is our reference spec, from four swinging gates we built for Arcadia NSW. Those gates were hot-dip galvanised rather than corten, so they prove the structural sizing at this scale rather than the patina. They run Foresee 900 motors and carry a Ghost Gum pattern. One project shows the sizing works. It does not set the spec for every gate.

The frame and the skin do different jobs in typical workshop practice. Frames run 3 to 5mm, infill panels run 2 to 4mm, and large sliding gates need 4 to 6mm structural members. 1.6mm cladding works on a 25 by 25mm box frame for lighter pathway gates. The frame carries the load, the skin carries the look, and the thickness follows the job each part does.

Automation adds load that the frame must carry. A gate with a motor needs a stiffer frame than a manual gate of the same size. Mention automation in your brief so the frame is sized for it from the start. See our driveway gate cost guide and our gates range.

Letters and Numbers, 3mm

COR10 3mm 3D corten steel house numbers 67 with Tweeddale lettering installed in a garden
Our 3mm 3D corten steel numbers installed at 67 Tweeddale.

3mm is the steel we use for 3D letters and numbers. That is our workshop spec, confirmed on our own jobs.

The grade context supports it. 3mm sits at the bottom of BlueScope’s HW350A range of 3 to 10mm. It is rigid enough for wall mounting and cuts crisply on the laser.

Near the sea, 3mm needs detailing that dries and a sealing plan. We cover both at quote stage.

COR10 3mm 3D corten steel letters spelling AWAR for Agnes Water Active Riders lit up at night
Our 3mm 3D corten steel letters for Agnes Water Active Riders.

Bigger work needs more steel in any case. The US signage industry works from 3.2 to 6.35mm for dimensional letters, and deeper returns need thicker material. Our 3mm suits the house number and signage sizes we build. See our house number size guide, our 3D letters, and our 3D numbers.

Thickness Is Not the Whole Story

Design often beats raw thickness. A folded 2mm edge beats a flat 3mm sheet, because folds add stiffness without adding weight. Metfab in Melbourne describes flat thin sheet as wobbly.

Weld sequencing controls warping as much as gauge does. Short staggered welds beat one long hot pass. That is the lesson of Fireball Tool’s 1.2 million view fabrication video on keeping projects from warping.

Returns, ribs, and cross bracing do the work of extra millimetres. A good fabricator designs stiffness in. A bad one just buys thicker steel.

Cutting method matters too. Plasma cutting leaves an oxidized edge on corten, so every edge needs grinding. Water jet cutting avoids the problem. That detail comes from Jay Sikora, an Australian maker who builds corten sculpture on camera.

What the Steel Yard Actually Sells

0.7 to 2mm is BlueScope’s CW300A range, 3 to 10mm is HW350A, and 6 to 80mm is WR350A. Those are the Australian weathering steel grades from the REDCOR technical bulletin.

WR350A, HW350A, and CW300A are the grades we use, to AS/NZS 3678, 1594, and 1595. High phosphorus grades come in the thinner ranges. They weld cleanly and resist corrosion well. See our grades explained guide for how they compare.

SSAB notes growing interest in the 3 to 8mm thin range. The industry is moving toward thinner weathering steel as confidence in the patina science grows. Our 3mm letters sit right in that movement.

Planning a custom corten piece? Tell us the product and the size. We will quote the right thickness for the job, not the thickest steel we can sell you.

Get a quote, cor10steelbyronbay.com.au/quote/

Frequently Asked Questions

How long will corten steel last?

Decades is the honest answer for atmospheric exposure, because the patina nearly stops corrosion once it stabilises. 32 years is how long SSAB’s Finland field test ran, with corrosion dropping drastically after the first 5 years. Buried steel and permanently damp steel are the exceptions, since the patina never forms there.

What thickness do I need for a corten gate?

Our Arcadia reference used 3mm steel at around 250kg per gate, hot-dip galvanised, running Foresee 900 motors. As a general guide, 3 to 5mm suits frames and 2 to 4mm suits infill panels, while 1.6mm cladding works on a 25 by 25mm box frame for lighter pathway gates. Tell your fabricator if the gate will be automated, because the motor adds load the frame must carry.

Can I use corten steel near the sea?

Sometimes, with honest limits. The FHWA’s Technical Advisory 5140.22 lists coastal environments among those where uncoated weathering steel should be used with caution, because airborne chlorides stop the patina forming. Our professional position is to let seaside pieces weather 12 months, then seal with Penetrol and reapply when it fades.

Does thicker corten steel cost a lot more?

Yes. Steel is sold by weight, and each millimetre adds 7.85kg per square metre. Thicker steel also costs more to cut and weld. That is why thickness should match the job, not the fear.

Why do you use 3mm for letters and numbers?

3mm sits at the bottom of BlueScope’s HW350A range and is rigid enough for wall mounting while cutting crisply. It suits the house number and signage sizes we build. Larger dimensional letters need thicker steel, which we quote per project.

Sources

  • Peer reviewed patina study, 14 samples, X-ray diffraction, corrosion under 0.01mm per year, patina formation over 3 to 7 years, pmc.ncbi.nlm.nih.gov/articles/PMC8306178
  • SSAB 32 year COR-TEN B field test Finland 1982 to 2014, corrosion dropped drastically within 5 years, growing interest in 3 to 8mm, ssab.com
  • SSAB weathering steel, final patina appearance 2 to 6 years, ssab.com
  • steelconstruction.info weathering steel, corrosion allowances C1 0.0, C2 0.5, C3 1.0, C4 1.5mm per face, C5 and CX not recommended, UK bridge design context, steelconstruction.info/Weathering_steel
  • BlueScope REDCOR technical bulletin 26, CW300A 0.7 to 2mm, HW350A 3 to 10mm, WR350A 6 to 80mm, via edconsteel.com.au (PDF)
  • FHWA Technical Advisory 5140.22, Uncoated Weathering Steel in Structures, coastal and high humidity environments need caution, fhwa.dot.gov/bridge/t514022.cfm
  • AZoM, The Application of Corten in Signage, Battle of Bannockburn memorial, 5mm laser cut plate over 10mm backing, azom.com/article.aspx?ArticleID=11102
  • Metfab Melbourne, corten thickness specification guide, 3mm the sweet spot for edging, folds and stiffeners matter as much as thickness, metfab.com.au/how-to-specify-corten-steel-for-your-builder
  • COR10 Steel, Arcadia NSW project, four swinging gates, 3mm hot-dip galvanised steel, around 250kg each, Foresee 900 motors, Ghost Gum pattern, via our gates page

Watch

Related Reading on COR10 Steel

Similar Posts

Leave a Reply

Your email address will not be published. Required fields are marked *