Corten Steel House Numbers: What to Know Before You Buy

Corten steel parcel box with rust patina at EDEN garden centre, Byron Bay

Corten steel house numbers combine visibility, durability, and a finish that gets better with age. The right size depends on how far the numbers sit from the street. Some Australian councils require at least 75mm numerals on the building. The market splits between cheap laser-cut digits and large architectural 3D numbers. This guide covers sizing, mounting, materials, and what to watch for before you buy.

What Size House Numbers Do You Need?

Match the number height to the viewing distance from the street. Australian councils that publish minimums generally require 75mm numerals on the building exterior. As a practical rule, 100mm numbers suit houses close to the footpath, 150 to 200mm suit standard suburban setbacks, and 300mm or larger suit properties set well back from the road or rural blocks. If emergency services cannot read your number from a moving vehicle, it is too small.

There is no Australian national standard for house number sizes. Australia Post requires prominent numbering but states no minimum. The 75mm figure comes from councils such as Newcastle NSW and Nedlands WA. When in doubt, go one size larger than you think you need.

Our 3D numbers start at 50cm, which suits gates, fences, large facades, and rural blocks where the number sits well back from the road. Smaller custom sizes are available on request.

3D Numbers vs Flat Numbers

3D numbers are more visible than flat numbers at the same height. The depth creates shadows that define each digit, especially in angled sunlight. A floating mount with a 30mm standoff gap amplifies this effect and gives the numbers a premium architectural look. Flat laser-cut digits sit flush against the wall and rely entirely on colour contrast.

Our 3D numbers are true three-dimensional block forms in 3mm corten steel, not flat cut-outs. They come in 50, 100, and 150cm sizes. The depth is what makes them readable from down the street and what separates them from the flat digits most sellers offer.

Custom 3D corten steel number 2 with Wildthorn Ave cut into the side
Custom 3D number 2 with street name cut-out, fresh from the workshop.

Why Corten Steel for House Numbers?

Corten steel needs no painting, never peels, and develops a protective patina that suits Australian conditions. Unlike powder-coated aluminium, there is no coating to chip or fade. Unlike stainless steel, there is no tea-staining near the coast. Unlike acrylic, it will not go brittle in the sun. The rust-brown patina reads clearly against light-coloured render, which covers many Australian homes.

We pre-weather every number with a four-week seawater cure in direct sun, so it arrives with the patina already developed. Many Australian sellers ship corten numbers raw or chemically treated. Ours are ready to mount and will weather evenly from day one. We build in Australian high-phosphorus weathering grades WR350A, HW350A and CW300A.

Large 3D corten steel numbers 138 installed in Mount Tamborine Queensland
3D numbers in Mount Tamborine, Queensland, after 4.5 years outdoors.

One caveat for coastal properties: salt air can prevent the patina from stabilising properly. If your home sits close to breaking surf, read our guide to how long corten steel lasts before choosing corten for an exposed facade.

Corten steel number 1 on a driveway post in Ormeau Queensland with dark established patina
Number 1 in Ormeau, Queensland, with a darker established patina after 5.5 years.

What About Rust Stains on the Wall?

Runoff staining is the most common concern with corten, and pre-weathering reduces it significantly. Fresh corten sheds loose rust particles during the first months of weathering, which can stain the wall below. Because our numbers arrive pre-weathered through the seawater cure, most of the loose initial runoff has already happened in our workshop. The patina keeps maturing after installation, so minor runoff can still occur, but far less than with raw steel.

Standoff mounting keeps the steel off the wall surface for ventilation and drying, as recommended in SSAB’s design guidance with a 30mm gap. For extra runoff protection, a penetrating sealer can be applied, though this will darken the finish.

How Do You Mount Them?

Threaded studs fixed with epoxy adhesive is the standard method for masonry walls. Drill holes slightly larger than the pins, clean out the dust, pipe in a two-part epoxy such as Chemset from Bunnings, and set the pins. The numbers may need temporary taping until the epoxy sets. For timber, use stainless steel screws into pilot holes. A 30mm spacer behind each digit creates the floating effect and allows airflow.

If you are not comfortable drilling into brick, any handyman can do this in under an hour. The key detail is getting the spacing even, so use a paper template to mark the pin positions before drilling.

What Do They Cost?

The Australian market splits into two tiers. Laser-cut flat corten digits in 200mm run roughly $34 to $90 per digit from Australian sellers on Etsy and eBay (prices checked October 2026). Larger architectural digits in 400 to 600mm run $121 to $297 per digit. Our 3D numbers run $645 to $1,495 per number in 50, 100, and 150cm sizes. The price reflects true three-dimensional fabrication in 3mm plate plus the four-week seawater cure, not just laser cutting.

Be wary of listings that use “corten” in the heading but sell powder-coated stainless or chemically rusted mild steel. Real corten is a specific weathering steel grade. Ask the seller for the grade if it is not stated.

Large 3D corten steel letter R for the Agnes Water Active Riders Queensland
3D letter R for the Agnes Water Active Riders, Queensland.

Will They Be Visible at Night?

Corten steel is non-reflective, so it needs external lighting after dark. This is the genuine disadvantage compared to reflective or backlit numbers. If night visibility matters, mount a small spotlight or use existing porch lighting aimed at the numbers. The 3D depth helps here too, as side lighting throws shadows that define each digit.

On light-coloured walls, the dark rust patina gives strong daytime contrast. On dark brick or timber, consider a light-coloured backplate behind the numbers to maintain readability.

Ready to make your street number unmissable? Browse our pre-weathered 3D numbers or get a custom quote.

Shop 3D Numbers

Frequently Asked Questions

What is the minimum legal size for house numbers in Australia?

There is no national standard. Councils that publish minimums generally require 75mm numerals on the building exterior. Australia Post requires prominent numbering but states no minimum size. Check with your local council for specific requirements.

Do corten steel house numbers rust onto the wall?

Fresh corten can shed rust particles that stain walls below. Our numbers arrive pre-weathered through a four-week seawater cure, so the initial runoff happens in our workshop. Standoff mounting keeps the steel off the wall surface as extra protection.

How long do corten steel house numbers last?

In suitable conditions, decades. The protective patina slows corrosion to a very low rate once stabilised. Keep them off the ground, away from constant salt spray, and out of permanently damp positions. See our guide to corten steel lifespan for the full picture.

Can I install them myself?

Yes, with basic tools. Drill holes for the mounting pins, fix with two-part epoxy adhesive on masonry or stainless screws on timber, and use a paper template for even spacing. A handyman can do it in under an hour if you prefer.

What is the difference between your 3D numbers and laser-cut digits?

Laser-cut digits are flat shapes cut from sheet. Our 3D numbers are true three-dimensional block forms fabricated in 3mm corten plate, then pre-weathered with a seawater cure. The depth gives better visibility and a more architectural presence.

Sources

  • City of Newcastle NSW — development consent condition, 75mm building exterior numerals.
  • City of Nedlands WA — Assignment of House Numbers Policy, 75mm minimum.
  • Wollongong City Council — kerbside house numbering guide, 80mm reflective numerals.
  • Toowoomba Regional Council QLD — Rural and Urban Addressing Policy 2025, 75mm Series D.
  • City of Vincent WA — kerb numbering information sheet, 140mm yellow reflective.
  • Brisbane City Council BSD-2004 — kerb numerals 80 to 130mm.
  • NSW Local Government Act 1993 s124 Order 8 — council power to order number display.
  • SSAB — COR-TEN design guide, runoff staining guidance and 30mm ventilation gap.
  • Hibernate Outdoors — corten steel numbers installation guide, Chemset epoxy method.
  • Kelly Metal — corten steel letters and numbers pricing, raw finish disclosure.
  • YouTube: Gardener’s Supply — How to Weathering Corten Steel. youtube.com

Similar Posts

Leave a Reply

Your email address will not be published. Required fields are marked *