Corten Steel Fence Cost Per Metre in Australia [2026 Guide]
A 1.8 metre corten steel fence in Australia typically costs $350 to $950+ per linear metre supplied and installed. COR10 makes its fence panels 1.8 metres high by 1.4 metres long from 2mm corten. Plain panels run $110 to $250 per linear metre supply-only, while laser-cut feature panels run $250 to $500+ per panel. A comparable Colorbond fence installs for $110 to $160 per metre.
This guide breaks down the per-metre cost, what moves it, how installation differs from ordinary fencing, and the council and neighbour rules that apply. For our fence design options, see corten fence ideas for Australian homes. For general corten pricing, our cost guide covers panels and products.
What a corten fence costs per metre
| Component | Rate | Source |
|---|---|---|
| Plain 2mm panel, supply only | $110–$250 per lin m | COR10 client-supplied figure, October 2026 |
| Laser-cut 2mm panel, supply only | $250–$500+ per panel | COR10 client-supplied figure; panels 1.8m high × 1.4m long |
| Installation labour (frames, posts, footings) | $150–$300 per lin m | COR10 client-supplied contractor rates; varies with site complexity |
| Supply + install, 1.8m fence | $350–$950+ per lin m | COR10 client-supplied figure; plain panels at the low end, laser-cut feature panels at the high end |
These are COR10’s actual supply-and-install figures, not a component estimate. The project cost splits into two parts: the panels, and the professional labour to build the frames and install them. COR10 contracts installation to outside fencing contractors. Difficult sites, slopes and old fence removal all push the figure higher. Sloping ground alone can add 20 to 40 percent to installation labour, and old fence removal runs $15 to $30 per metre.
Corten vs Colorbond per metre
| Fence type, 1.8m installed | Per linear metre | Source |
|---|---|---|
| Colorbond, installed | $110–$160 | Jim’s Fencing, national AU franchise (strong) |
| Colorbond, installed, Melbourne 2026 | $130–$180 | Melbourne publisher, metro-specific (medium) |
| Corten, 1.8m, supply + install | $350–$950+ | COR10 client-supplied; plain panels at the low end, laser-cut feature panels at the high end |
Corten costs roughly two to six times a Colorbond fence per metre, and the gap is almost entirely the panel. Colorbond panels are a mass-produced commodity with published supply prices under $50 per linear metre. Corten panels are cut to order in small runs. Installation labour costs about the same for both.
What moves the per-metre price
Panel type moves the price most. Plain 2mm corten panels run $110 to $250 per linear metre supply-only, while laser-cut decorative panels run $250 to $500+ per panel. Height comes next. A 1.8 metre fence needs more steel and deeper footings than a 1.2 metre fence, and Melbourne 2026 figures show the same height effect for Colorbond. Thickness matters too. We usually make fence panels from 2mm to 3mm corten, and thicker panels weigh more and cost more per metre.
Site conditions are the quiet multiplier. Rocky ground, poor access, retaining requirements and old fence removal all add labour. Get the site assessed before comparing quotes, because two 20 metre runs on different blocks can price very differently.
How installation works
A panel fence is posts, footings, panels and fixings. Posts go into concrete footings at spacings set by the panel length plus the post width. For an 1800mm fence in firm earth, a manufacturer installation guide specifies 750mm deep holes, with 100 to 200mm extra in soft ground. Hole diameter should be the post width plus at least 100mm. Concrete needs 24 to 48 hours to cure before panels are hung.
We offer two fixing methods. Panels can have pre-drilled holes for screws that attach to support posts, or panels can clip or slide onto suitable posts for a cleaner face with no visible fixings. We can supply support posts as part of a custom fence project, and we plan panel design and support together because large panels catch more wind.
The install rules that are different for corten
This is where corten fencing diverges from ordinary fencing, and most installers get it wrong the first time. BlueScope’s advisory bulletin for REDCOR weathering steel states it plainly. The steel is not suitable where it is constantly wet, such as submerged in water, buried in soil, or in areas of very high rainfall and humidity. Fence panels must never be buried. Keep the base clear of soil contact and standing water, with airflow underneath.
Runoff needs planning before fabrication. Water running over weathering steel during patina development can stain concrete, pale pavers, rendered walls and unglazed brick. We consider panel position, ground levels and drainage before fabrication so water has a suitable path away from the installation. A gravel strip under the fence line is the simplest defence.
Fixings need isolation. BlueScope specifies 304 or 316 grade stainless steel screws with an isolating gasket, such as EPDM washers, between the two steel types. Corten must also be isolated from zinc-coated or ZINCALUME support structures with heavy-duty isolation tape. Eliminate any joint or crevice where moisture or debris can sit, because trapped water corrodes instead of weathering.
Two smaller points from the same bulletin. Bare hands leave oils that mark the patina for an extended period, so gloves during installation matter. And within about 2km of breaking surf, weathering steel needs project-specific assessment rather than standard details.
Council rules and neighbour costs
In NSW, exempt development rules set the general pattern. Side and rear boundary fences can go to 1.8 metres, while fences on a street frontage or road setback are limited to 1.2 metres. Always check the local council DCP, because overlays and heritage areas change the rules. In Byron Shire, Chapter D1 of the Development Control Plan limits front fences to 1.2 metres and side and rear fences to 1.8 metres, with a 50 percent visual permeability requirement above 1.2 metres for taller front fences.
Who pays is settled law. Under the NSW Dividing Fences Act 1991, adjoining owners share the cost of a sufficient dividing fence equally. The honest catch for corten buyers is the word sufficient. A corten fence almost certainly exceeds the sufficient standard, so a neighbour can only be compelled to contribute to the cost of a basic fence. The owner who wants corten pays the upgrade gap. The same principle applies in Queensland and Victoria under their own dividing-fence legislation. Talk to the neighbour and get the agreement in writing before ordering steel.
Corten fences and bushfire zones
Steel fencing is one of the few materials that gets better in a bushfire zone. The NSW Rural Fire Service lists noncombustible fences as the most effective at withstanding intense bushfire heat, and its home preparation guidance tells residents to replace wood fences with metal fences. CSIRO and Bushfire CRC testing with BlueScope found steel fencing offered greater protection to homes than alternative materials because of its non-combustibility.
Corten is solid steel, so it is non-combustible. In a BAL-rated area, a corten fence is both a boundary and a fire-resilience measure, where a timber paling fence is fuel. That dual role is worth weighing against the higher per-metre cost.
When a corten fence is not worth it
A decorative corten panel should not automatically be treated as a compliant pool barrier. Pool fencing has its own height, gap and non-climbable zone requirements, so confirm compliance before fabrication. Within about 2km of breaking surf, standard weathering details may not apply and the project needs individual assessment. Any position where the fence would sit in permanently damp ground, against irrigated garden beds, or where sprinklers constantly wet it will weather badly. And for a plain side boundary where nobody sees the fence and the budget is tight, Colorbond at half the price is the rational buy.
Frequently asked questions
How much does a corten fence cost per metre in Australia?
Budget $350 to $950+ per linear metre supplied and installed for a 1.8 metre fence. Plain 2mm panels cost $110 to $250 per linear metre supply-only, laser-cut feature panels cost $250 to $500+ per panel, and installation runs $150 to $300 per linear metre depending on site complexity. Our cost guide covers general corten pricing.
Is a corten fence more expensive than Colorbond?
Yes, roughly two to six times per metre installed. A 1.8 metre Colorbond fence installs for $110 to $160 per metre through national franchises, while corten lands at $350 to $950+ supplied and installed. The panel is the difference. Installation labour costs about the same.
Can I install a corten fence myself?
The posts and footings are standard fencing work, but the weathering-steel detailing is not. Panels must stay clear of soil and standing water, runoff needs a planned path, and fixings need stainless screws with isolating washers. Get those wrong and the fence corrodes instead of weathering.
How long does a corten fence last?
Decades, in the right position. The patina greatly slows further corrosion once it stabilises, which is why corten needs no repainting cycle. Buried bases, constant wetting and salt exposure shorten its life sharply. Our guide to what corten steel is explains how the patina forms.
Will a corten fence stain my concrete or pavers?
During the first one to three years of weathering, yes, it can. Rust runoff marks concrete, pale pavers and rendered walls. Plan a gravel strip or dark surface below the fence line and keep runoff off pale materials. This is the most common surprise for new corten owners.
Does my neighbour have to pay half for a corten fence?
Only for the cost of a sufficient basic fence. Under the NSW Dividing Fences Act 1991, neighbours share a sufficient dividing fence 50/50. Because corten exceeds that standard, you pay the difference between basic and corten. Agree it in writing first.
Sources
- Lysaght Product Advisory Bulletin PAB12 — REDCOR weathering steel (no burial or constant wetting, runoff staining control, 304/316 screws with EPDM washers, 250-micron isolation tape, 2km coastal setback). lysaght.com
- SSAB — COR-TEN product page (hot-dip galvanised, weathering steel or stainless bolts feasible; connections tight and compact). ssab.com
- NSW Rural Fire Service — Prepare Your Home (replace wood fences with metal fences; noncombustible fences most effective against bushfire heat). rfs.nsw.gov.au
- CSIRO / Bushfire CRC — residential boundary fence fire testing with BlueScope (steel fencing’s non-combustibility protects homes). library.dbca.wa.gov.au
- Legal Aid NSW — dividing fences rights and obligations (50/50 sharing of a sufficient fence; higher standard paid by requester). legalaid.nsw.gov.au
- NSW Government Planning — exempt development fence rules (1.8m side/rear, 1.2m street frontage). planning.nsw.gov.au
- Jim’s Fencing — Colorbond installed $110–$160/m nationally (strong AU benchmark). jimsfencing.com.au
- Yarra Outdoors — laser-cut corten panels $129–$299 AU retail (strong AU panel prices). yarraoutdoors.com.au
- Gates Plus — steel post pricelist (post cost benchmark). gatesplus.com.au
- ServiceTasker — AU fencing cost guide 2026 (install labour $70–$85/m; Colorbond $85–$200/m; medium source). servicetasker.com.au
- House Digest — corten fence overview (US$75–150/linear foot installed, unsourced; runoff and no-burial notes). housedigest.com
- COR10 — client-supplied fence pricing, October 2026 (panel and installation rates for 1.8m × 1.4m 2mm panels; installation via contracted fencing contractors).