Corten Steel Retaining Walls in Australia

Corten steel panels, 2mm, during curing

A Corten steel retaining wall in Australia can hold a slope, a terrace, or a garden bed, and it can fail if drainage, buried steel, and council rules are left until last. A low edge at 240 millimetres, a modular wall at 900 millimetres, and a tall wall over 1 metre are three jobs.

By COR10 Steel, Byron Bay. We fabricate Corten steel, supply Australia wide. We supply a new COR10 retaining wall product, described below. This guide helps you buy or commission a Corten retaining wall in Australia with confidence.

Subscribe to COR10

Monthly Corten steel news, blogs and offers.

Get monthly Corten price updates and project ideas

A garden edge, a modular wall, and a custom wall are not the same job

Straightcurve edging is the lightest job. Its Ridgidline and Flex edging is 2 millimetres thick, in 2.2 metre lengths, from 75 millimetres to 560 millimetres, with a 10 year warranty, and Straightcurve gives 240 millimetres under 15 percent slope, 400 millimetres from 15 percent to 25 percent, and 560 millimetres over 25 percent. A modular system is heavier. Cor-Ten Steel Australia describes an engineer designed system with Corten angle posts in concrete pile holes, pile depth generally at least equal to wall height. Our custom route is the new product in the next section. Our standard fence panel is 2260 millimetres by 1000 millimetres, 2 millimetres thick, from $395 GST included, and we do not rate it for soil retention.

Our new retaining wall panels lock together, and soil or pebbles hold the back

We supply panels that lock together for a wall, instead of blocks or stone. Each panel is between 2 millimetres and 3 millimetres thick, its length can be customised, and its maximum height is 1.2 metres. Screws connect each panel to the next panel, and screws connect the panels to a solid surface. The back is filled with soil or pebbles for extra support. The product is architectural as well as structural, and customisable with inscriptions or artwork, just like our panels.

Our panels arrive after our 4 week seawater cure, the same cure used for our letters, numbers, sculptures, and parcel boxes. If installation is requested we can arrange it. At 1.2 metres, check the council and engineering rules below before you install, because height, boundary, and surcharge can change whether a permit or engineer is needed.

COR10 Corten steel retaining panel
COR10 retaining panel. Single rusted panel with triangular side support.
SpecificationOur new retaining panel
ThicknessBetween 2 millimetres and 3 millimetres
Maximum height1.2 metres
LengthCan be customised
FixingsScrews between panels, and screws to a solid surface
Back supportSoil or pebbles filled at the back
CustomisationInscriptions or artwork, just like our panels
Cure4 week seawater cure
InstallationCan be arranged on request

Drainage comes before beauty, and water decides if a wall stands

Drainage is structural. PB Engineering says hydrostatic pressure is the leading cause of retaining wall failure in Australia, and puts water alone at about 15 kilopascals at the base of a 1.5 metre wall. Most guides agree on a 100 millimetre perforated ag pipe, aggregate at least 300 millimetres wide, geotextile, and discharge. Pipe fall disagrees by source, with block guides giving 1 in 100, the National Construction Code giving a minimum of 1 in 300, and a Queensland drawing giving 1 in 80. Follow your engineer’s drawing for fall for your site, and do not treat any one of those three figures as a universal rule. Weep holes do not replace that system.

Buried steel does not weather like exposed steel

Exposed Corten forms patina through wet and dry cycles, buried steel does not get that cycle. SteelConstruction.info says where continuously wet conditions cannot be avoided, a corrosion rate similar to ordinary steel must be expected. Cor-Ten Steel New Zealand and Australia say buried Corten generally loses about 0.5 millimetres every 5 years to 10 years, and their fix is bitumen paint on the back before backfilling, with SikaTite BE or Sika Blackseal Plus cited. That coating is a moisture barrier, not a patina substitute. Our panels arrive after our 4 week seawater cure, the same cure used for our letters, numbers, sculptures, and parcel boxes. Whether the back of our retaining panel is coated before backfilling, and how long a buried panel is expected to last on your site, must be confirmed in your quote, because thickness alone does not decide a buried wall.

Council and engineering rules change at the border, and at the boundary

There is no single national height rule in Australia. AS 4678 applies to walls over 800 millimetres and under 15 metres at 70 degrees or more, and that figure is a design scope threshold, not a permit threshold. Check your local council for your site, because boundary, surcharge, and tiered walls change the answer.

State or territoryTriggerNotes
New South WalesExempt to 600 millimetres, complying to 1 metre, development application over 1 metreCheck your local council
Western AustraliaPermit over 500 millimetres, or at any height with other building workOther work matters at any height
QueenslandApproval avoided only if every trigger is clearNo more than 1.0 metre, no surcharge, at least 1.5 metres from a building or wall, no pool barrier, wall plus fence under 2.0 metres
VictoriaPermit over 1 metre, and over 0.6 metres near a boundarySome councils require a boundary permit at 600 millimetres
South AustraliaApproval over 1 metreTiered walls counted together
TasmaniaNo single figure, check your local councilSources disagree
Northern TerritoryExempt to 600 millimetresBuilding Note 114, August 2025
Australian Capital TerritoryCheck your local councilBoundary and surcharge rules vary

Runoff will stain pale paving, so plan a buffer first

While the patina is still forming, rainwater can carry rust onto pale stone, concrete, or pavers. Cor-Ten Steel Australia puts that phase at 3 months to 9 months, and gives a 50 millimetre to 100 millimetre gravel strip between wall and patio. Runoff duration is disputed, with Corten Ireland saying it stops entirely once stabilised, and Adezz saying it may still occur but be minimal. Archclad says salt spray applications are not recommended unless painted.

What a Corten retaining kit costs in Australia, and what it does not include

No Australian Corten retaining installed price is published in this guide. The only published Australian Corten retaining prices are kit prices from Cor-Ten Steel Australia, for average soil, flat land, and no surcharge loads. GST status and inclusions are not published on the kit page checked, so check that page before you compare a kit price with an installed price, and check whether posts, drainage, excavation, delivery, or installation are included. A straight kit 3.13 metres by 450 millimetres is $1,381.55, and a straight kit 6.43 metres by 1200 millimetres is $8,819.27. Those are kit prices, not installed, not COR10. Our raw sheet is $385 for 2 millimetres and $650 for 3 millimetres per square metre, plus GST, supply only.

Terraces, slopes, and small drops, where Corten works best

Corten works best where the job is small, drained, and broken into levels. Straightcurve says a sloping garden works when you stop fighting the grade and start designing with it. Lowndes Landscapes gives a similar rule for Corten bands under 1 metre, maximum bandwidth 300 millimetres. Tiered walls are usually assessed together. Good uses are low garden walls, raised beds, and terraces, not constantly wet soil, tall walls without design, or surcharge loads without engineering.

COR10 Corten steel retaining panel, front view
COR10 retaining panel, front view. Rusted panel with side support and fixing holes.

Related reading. Our cladding cost guide, Brisbane guide, Byron Bay guide, grades guide, and letterbox guide.

What to send for a quote, and what we cannot quote without a site

Send a drawing, or a sketch. Add dimensions, drop, length, soil type, whether ground behind is flat or sloping, whether a driveway, building, pool, or second wall sits near it, and delivery suburb and date. Say plainly if the job is near the sea or a pool, or clay soil. What we cannot quote from this page alone is post spacing, pile depth, footing, back coating, a drainage specification for your site, delivery charge, lead time, or warranty, because those depend on your site and job.

Ask us for a retaining wall quote.

Get a free quote. Send your sketch or drawing, with drop, length, soil, surcharge, boundary, and delivery suburb. You can also call 0439 668 614.

Questions retaining wall buyers ask

Can I use a COR10 fence panel as a retaining wall?

We do not rate our 2260 millimetre by 1000 millimetre, 2 millimetre fence panel for soil retention. For soil retention use our new retaining panels above, not a fence panel, and do not assume a fence price is a retaining price.

Does a Corten retaining wall need drainage?

Yes. Drainage is structural, with a 100 millimetre perforated ag pipe, aggregate at least 300 millimetres wide, geotextile, and a legal discharge point.

Will a Corten retaining wall stain my paving?

It can, especially in the first 3 months to 9 months, and pale stone, concrete, and pavers are most at risk. Plan a 50 millimetre to 100 millimetre gravel strip between the wall and the patio.

Do I need council approval or an engineer for a retaining wall?

It depends on your state, council, height, boundary, and surcharge. Check the council table above for your state, then check your local council, because height, boundary, and surcharge change the answer. AS 4678 scope is over 800 millimetres, and that is a design scope, not a permit rule.

Similar Posts