Custom Corten Steel Gates in Byron Bay
Custom corten steel gates in Byron Bay are made to order, quoted per job, and made for one opening.
COR10 custom gates start from A$2750, GST excluded. That starting price includes the owner’s choice of artwork on the gate. Automation, posts, finish, delivery, and installation scope are stated in your written quote.
COR10 Steel Byron Bay is a Byron Bay corten steel workshop. It makes gates to order, with no stock held, and it supplies Australia-wide. Your gate is not ordered off a shelf. It is made for its opening, its wind, its driveway, and its sea distance, and those four facts decide the quote. For swing and sliding designs and pattern examples, see COR10’s custom driveway gates in Byron Bay page.
Get monthly Corten price updates and project ideas
What a Byron Bay corten gate costs
Ask what is inside the quote, before you compare two gate prices.
That starting price buys a custom gate made for your opening, with your choice of laser-cut artwork, 3mm structural panels, 2mm infill, grades WR350A, HW350A and CW300A, and a 4 week seawater cure.
A complete gate price depends on gate type, opening width, height, solid or open pattern, frame, posts, hinges, finish, delivery, unloading, installation, and automation, if automation is wanted. Every custom gate is assessed against its opening, design, hardware and site conditions. Your written quote should specify the steel grade, panel thickness, included hardware, automation, delivery and installation scope.
For comparison, generic automatic gates in Australia are often quoted $3000 to $10000 installed, according to BMGI, published in 2021. Those are generic gates, not COR10 corten gates, and not a COR10 quote.
Want a COR10 gate price for your opening?
Get a free quote. Send the opening width, height, gate type, pattern, sea distance, and suburb. You can also call 0439 668 614.
Driveway, pedestrian, swing, sliding, and cantilever gates
The driveway decides the gate type, before the pattern is chosen.
A driveway gate closes a vehicle opening. A pedestrian gate closes a walk opening. Swing suits a flat driveway with room to open. Sliding and cantilever suit a tight or sloped driveway. Order by your measured opening in millimetres, not by a standard size. A solid leaf gives privacy and a full rust face, and it catches wind. An open pattern gives airflow and a lighter look, and it lets wind through. For full swing, sliding, and pattern designs, see COR10’s custom driveway gates in Byron Bay page. This page is for Byron buying, price, lead time, sea, runoff, and quoting, not a second design guide.
Opening width, weight, and wind
A solid leaf acts like a sail, so hinges, posts, and operator must be sized for wind, not weight alone.
A 3mm sheet at 1200 by 3000mm weighs about 84 kilograms. That is a sheet weight, useful for lifting and unloading, not a gate leaf weight. A finished leaf is heavier once frame, posts, hinges, and operator are added, and a solid leaf adds wind load on top of that weight. Send the opening width, height, pattern, and wind exposure with your quote. A sheltered street and an exposed headland are different wind sites, even at the same opening width.
Posts, hinges, frame, and pattern
A gate price without posts, hinges, and frame is not a gate price.
Your written quote should specify whether posts and footings are included or separate, and who sets them, whether hinges are included and what type they are, whether the frame is included and how its ends are drained, so water does not sit inside a tube, whether the pattern is solid, laser-cut, or open, and whether fasteners are stainless or weathering steel, with isolation from galvanised steel, because dissimilar metals can stain a corten face. COR10 gates use 3mm structural panels and 2mm infill, in grades WR350A, HW350A and CW300A. Support posts are customised SHS Posts, in various finishes and sizes.
Automation on your gate
Automation is a separate job inside a gate quote, and it must be stated as included or not.
COR10 supplies automation for gates at cost price as part of its service. Installation is available for some projects, so confirm installation for your project in your quote. Confirm what power is available at the gate line, 240V, DC, or solar, and what access you want, remote, keypad, or intercom. Check Australian safety requirements for your gate in your quote.
Runoff at the gate line
Plan the driveway below the gate, before the gate is made.
While the patina forms, runoff stains concrete, stone, and brick, most intensely at first. Plan a drip edge, a gravel or planting strip under the gate line, sealed pavers or concrete below, a bottom rail clear of flatwork, and drainage, with no pooling against steel. Drainage, ground levels, water paths, and materials around the gate are checked before fabrication. Send the driveway material below the gate line with your quote, so the runoff plan can be stated for your site.
Your gate near the sea
Seaside sites are assessed case by case, not by a beach promise.
General guidance cautions against marine exposure where steel never dries, while other guides say coastal use is possible with care, thicker plate, and rinsing. COR10 has no standard protocol for every block. Every COR10 gate goes through a 4 week seawater curing process before delivery, with seawater applied daily in direct sun over about 4 weeks to build the golden rusty patina, with no chemical accelerants. Penetrol sealing is done after 12 months, depending on the owner, by the owner. Send sea distance, spray, shelter, and drying with your quote, so COR10 can assess your gate site on its own facts.
Arcadia, a gate and fence project
Arcadia, NSW, shows a gate and fence set built around a site, in full.
That project included four swinging gates in hot-dipped galvanised steel with a custom Ghost Gum pattern, plus 23 customised Corten steel fence panels carrying the matching pattern. The gates were galvanised, not corten, and the fence panels were corten. Each gate is 3mm steel and weighs about 250 kilograms, driven by four Foresee 900 motors, up to 375 kilograms per gate. Custom gate fabrication typically takes 10 weeks from approval of the final 3D drawings.
How your gate gets to you, and what to send for a real quote
Send the checklist below, and your quote will not be returned as a question.
Send gate type, opening width and height, pattern and privacy, automation and power, sea distance and wind exposure, driveway material below the gate line, and unloading access. COR10 will confirm grade, thickness, hardware, automation, delivery and installation scope, GST, and lead time, typically 10 weeks from approval of the final 3D drawings, in your written quote.
Get a corten quote.
Get a quote. You can also call 0439 668 614.
Frequently Asked Questions
How much does a custom corten steel gate cost?
From A$2750, GST excluded, including the owner’s choice of artwork. Full scope for frame, posts, hinges, pattern, finish, delivery, installation, and automation is confirmed in your written quote.
What size gate does my driveway need?
Measure your opening in millimetres, width and height, and send whether it is a driveway or pedestrian opening. No standard corten gate size is printed, size is confirmed for your exact opening in your quote. Melbourne steel guides use about 1000mm for a pedestrian gap and about 3000mm for a driveway gap.
Swing, sliding, or cantilever for your block?
Swing suits a flat driveway with room to open inwards or outwards and strong posts. Sliding needs a track or cantilever system and groundwork, and suits a tight or sloped driveway. Cantilever hangs from a track system without a ground track, and needs room to slide back beside the opening. Send your driveway shape, slope, and space, and the type is confirmed in your quote.
Can a corten gate be automated?
Yes. COR10 supplies automation for gates at cost price as part of its service. Installation is available for some projects, so confirm installation for your project in your quote. Power, 240V, DC, or solar, and access, remote, keypad, or intercom, are stated in your quote.
Will a corten gate stain my driveway?
Yes, while the patina forms, runoff stains concrete, stone, and brick, most intensely at first. Plan a drip edge, a gravel or planting strip under the gate line, sealed pavers or concrete below, a bottom rail clear of flatwork, and drainage, with no pooling against steel.
Will a corten gate work near the sea?
COR10 assesses every seaside site case by case. Send sea distance, spray, shelter, and drying with your quote. Every COR10 gate goes through a 4 week seawater curing process before delivery, with seawater applied daily in direct sun over about 4 weeks, with no chemical accelerants. Penetrol sealing is done after 12 months, depending on the owner, by the owner.



