Corten Steel Cladding Cost Per m2 in Australia 2026 Guide
Corten steel cladding starts with a raw sheet price, and a finished wall is quoted per job.
Our raw corten sheet is $385 for 2mm and $650 for 3mm, per square metre plus GST, with the difference in price coming from the way it is cut, its profile, and whether it is A or B grade AS/NZS 3678 WR350. It is made to order, with no stock held, including custom lengths up to 4 metres, although cutting sheets over 3 metres often attracts a premium. Cladding is usually 2mm in thickness and it is supply only, with installation carried out by the buyer’s builder, so these corten steel panels are made to order rather than standard stock panels. A finished cladding wall is quoted per job, based on panel system, fixing, membrane, trims, scaffolding, freight, and GST.
Normally, most large fabricating companies can supply corten steel sheets up to 3 metres in length. We are one of maybe three companies that can supply customised corten steel sheets over 3 metres in length, and up to 4 metres if required.
Supply-only and installed are two different prices
Ask what is included, before you compare two quotes.
Supply-only is the sheet or panel only, while supplied and installed is the finished wall, with subframe, membrane, fixings, trims, scaffolding, labour, freight, waste, and GST. Handy Steel Stocks’ prices are GST included. Corten Australia quotes are AUD ex GST.
Market corten steel cladding prices to check against our raw sheet price
These are market supply-only prices, for comparison, not COR10 finished wall prices.
Handy Steel Stocks lists full sheets only, with no cutting, and no grade stated, so re-check the price before you rely on it. Handy Steel Stocks lists its sheets with a title area of 2440 by 1220mm and a specification area of 2400 by 1200mm.
| Product | Sheet price | Per square metre | Included |
|---|---|---|---|
| Handy, 1.6mm corten sheet | $154.80 GST included | $52.00 title area, $53.75 specification area | Supply only, full sheet, no cutting or installation |
| Handy, 3mm corten sheet | $287.28 GST included | $96.51 title area, $99.75 specification area | Supply only, full sheet, no cutting or installation |
| Lump faceted panel, 1100 by 2300mm, no lights | $2,420 GST included per panel | $956.52 derived, finished panel only | Wall mount only, excludes framing, delivery, installation |
Corten Australia, Melbourne, is a genuine SSAB COR-TEN trade supplier, quote only, 3.0mm flat sheet 1200 by 3000mm, minimum 10 sheets, raw material only. Lump is a finished sculptural panel, not a flat sheet, and must not be averaged with sheet prices.
Want a COR10 price for your wall?
Get a free quote. Send the measured wall area. You can also call 0439 668 614.
What an installed wall is made of
No Australian corten installed rate with a scope breakdown was published, so use this build-up to compare quotes.
Sculptform aluminium gives $360 to $420 per square metre standard, and $560 to $620 insulated, for 200 to 500 square metre projects, while Evodek composite gives $140 to $280, single-storey, with scaffold and membrane excluded. Neither is a corten price, so the build-up transfers, not the dollars.
| Build-up line | Check in your quote |
|---|---|
| Panel or sheet | Thickness, grade, panel size, finish |
| Subframe, fixings, membrane | Clip, fastener, cavity, membrane |
| Trims, flashings, scaffolding | Corners, reveals, scaffold height, duration |
| Labour, freight, waste, GST | Installer, offloading, crane, offcut rate, GST |
Thickness, panel size, and weight
At 7,850 kilograms per cubic metre, 1mm of steel is 7.85 kilograms per square metre before folds, fixings, or waste.
- 0.7mm flat-lock, 100 to 530mm wide, clips at 300mm centres, over 18mm plywood and membrane.
- 1.5mm cassette, 26.5mm deep, up to 875mm wide, 20mm recessed joint.
- 3.0mm flat sheet, 1200 by 3000mm, about 85 kilograms per sheet, and custom cassette at 1150mm wide.
None publishes a price, and none is a COR10 system, so for COR10 corten cladding, panel system, width, minimum order, waste, and freight for a long sheet are confirmed per job.
Worked wall sizes, sheet maths only
These sizes show sheet cost only, not wall cost.
Using Handy 3mm at $287.28 GST included, with 2.88 square metres per sheet, 15 square metres needs 6 sheets at $1,723.68, 30 needs 11 sheets at $3,160.08, and 60 needs 21 sheets at $6,032.88, sheet cost alone. At 1.6mm, the same walls are $928.80, $1,702.80, and $3,250.80. Those figures exclude cutting, subframe, membrane, trims, scaffolding, freight, waste, and installation. A $2,000 to $4,000 scaffold is $133 to $267 per square metre on 15 square metres, and $7 to $13 on 300, while a ground-level 15 square metre wall would usually use a mobile tower, not a full scaffold.
Fixing, joints, and runoff
Fixing, cavity, and joint width change the quote, and none is a single published figure.
- Fixing: exposed fastener is cheapest, concealed clip lets corten panels move, hook-on uses pre-welded hooks, welded looks seamless but replacement means cutting. Fasteners must be stainless or weathering, not galvanised without isolation.
- Cavity: typically 20 to 40mm, with a breathable cavity and wrap, or a stud, membrane, batten and air zone.
- Joints: 1 to 3mm clearance, 3 to 10mm open joints, and 10 and 30mm visual express joints, plus a 20mm cassette recess, a visual joint, not a movement gap. Steel moves 1.8mm for 3 metres at 50 degrees, and 4.8mm for 8 metres.
- Runoff: lower edge 50 to 100mm above ground, wall standoff 20 to 50mm, drip edge, dark gravel or scoria splash zone below, and no light paving, pale concrete, stone, or glass directly below during early weathering. Pre-weathering reduces early staining.
See our rust staining article, How to Stop Corten Steel Rust Staining Your Concrete and Pavers.
Coast and bushfire for a coastal wall
We assess coastal and BAL sites per job, with site photos, surf distance, spray, shelter, and drying.
Manufacturer guidance gives 1 to 2 kilometre cautions, while seller guidance says a few hundred metres can work with drying detailing. Neither is a cladding approval on its own. For the full coastal position, see our coastal article, Corten Steel Near the Coast, What Salt Air Really Does to It. On bushfire, steel is non-combustible, but a BAL rating covers the whole wall, not just the panel, turning on a sealed wall resisting ember ingress. We assess BAL sites per job, so send your BAL rating with the quote request.
Real weathering steel versus corten-look products
Real weathering steel forms a patina, stains while it weathers, and changes colour over months to years.
Corten-look coated products, for example a 25 year warranty coating, or panels listing Corten at 0.55mm, do not rust or develop a real patina. Ask which product you are being quoted, with thickness, grade, and finish stated.
Eight checks before you quote
Measured wall area. Height, width, openings, waste.
Thickness and panel system. Flat sheet, cassette, flat-lock, or standing seam.
Finish on delivery. Bright, pre-weathered, or sealed.
Fixing, subframe, cavity, membrane. Clip, fastener, cavity, membrane.
Trims, flashings, joints. Corners, reveals, joint width.
Runoff, coast, BAL. Drip edge, splash zone, surf distance, BAL rating.
Scaffolding, freight, GST. Height, duration, crane, freight, GST.
Install included or not. Supply-only, installation by the buyer’s builder, in writing.
Planning corten steel cladding in Australia?
Get a free quote. Tell us it is corten cladding, send a photo of the wall and the measured area. You can also call 0439 668 614.
Frequently Asked Questions
How much does corten steel cladding cost per square metre in Australia?
For COR10 raw sheet, the corten steel cladding cost per m2 is $385 per square metre plus GST at 2mm and $650 per square metre plus GST at 3mm, with the final figure depending on how the sheet is cut, its profile, and whether it is A or B grade AS/NZS 3678 WR350. Cutting sheets over 3 metres often attracts a premium, and a finished wall is quoted per job, not from this sheet price alone. That price is raw sheet only, made to order, with no stock held. For comparison, Handy Steel Stocks supply-only sheets are $154.80 for 1.6mm and $287.28 for 3mm, GST included, full sheet only.
Is that price supply-only or installed?
The $385 to $650 price is raw sheet only, not installed. Cladding is usually 2mm, supply only, with installation carried out by the buyer’s builder. A finished wall adds subframe, membrane, fixings, trims, scaffolding, labour, freight, and waste, and is quoted per job.
What thickness should corten cladding be?
It depends on the system. Australian systems include 0.7mm flat-lock, 1.5mm cassette, and 3.0mm flat sheet. COR10 cladding is usually 2mm. Panel system is confirmed per job.
Will corten cladding stain the wall below it?
Yes, while the patina is forming. Use a drip edge, gravel or scoria splash zone, 50 to 100mm bottom clearance, and a drained ventilated cavity. Avoid light paving and pale concrete below during early weathering.
Is corten cladding suitable near the coast?
We assess coastal sites per job, with site photos, surf distance, spray exposure, and drying conditions. Manufacturer and seller guidance conflict, and neither is a cladding approval on its own.
How to fix corten steel cladding?
Use an exposed fastener for the cheapest fix, a concealed clip to let corten panels move, or hook-on pre-welded hooks. Welded looks seamless, but replacement means cutting. Use stainless or weathering fasteners, not galvanised without isolation, with a 20 to 40mm cavity, breathable membrane, and a drip edge.
Can COR10 supply a single sheet over 3 metres?
Yes, up to 4 metres. Normally, most large fabricating companies can supply sheets up to 3 metres. We are one of maybe three companies that can supply customised sheets over 3 metres, and up to 4 metres if required.
Sources
- Handy Steel Stocks, handysteel.com.au
- Corten Australia, cortenaustralia.com.au
- Lump Sculpture Studio, lump.com.au
- Sculptform, sculptform.com
- Evodek, evodek.com.au



